| The fully automatic
shoelace tipping machine AM 75
VIDEO
AM 75 Produktionspeed: 6.600 laces per hour Guarantee: 2 years length of laces: 0,36 m - 2,40 m (AM 75) Cross Weight: 1.100 KG Country of Origin: Germany exchangeable die - boxes: interchangable with Artos dies and die - boxes |
 |
| On our machines you have the possibility to manufacture three
different
kinds of tipping:
tipping with acetate-tape, melting and fixing synthetic laces only by heat
On the machine AM 75 all kinds of shoe-laces can be
manufactured: |
 |
| Fully - Automatic Shoe-Lace Tipping Machine AM 75 Two Years Garantee: Weight: 1.100 KG: The machine has a weight of 1.100 KG. This is necessary and very helpful because during the production a lot of vibrations arise. The frog which wrapps the lace arround the four prong spiders moves sideward up to 2,40 m while it is turning its direction up to twice a second. As well twice a second the die-box is pressed together to form the end of the lace and to cut it. The big weight of 1.100 kg is very helpful and necessary to absorb the arising vabrations. Lenght of Laces: up to 2,40 m: The machine AM 75 is able to manufacture laces up to a length of 2,40 m. The machine AM 80 tipps laces up to a length of 3,50 m. |
 |
| Exchangeable Die - Boxes:
The tipping of shoe-laces is done by dies, which wrap the foil arround the lace, press together both (lace and tape) under high pressure and cut. According to the thickness of the lace, different sizes of dies are needed. The exchange of dies in the die-box, which is always necessary if you change form thinn laces to thick laces, will need approximate one hour. On our machine AM 75 the complete die-box can |
 |
| All Shafts run in Bearings: The main shafts like the driving shaft have a diameter of 45 mm and 40 mm. The power is transfered by double - chains and a 1,5 PS - motor, while all shafts of the machine run in bearings. The Teeth-bar and the Toothed Wheel have Modul 4: The transfer-carrier (Frog) runs with bearings on harden and polished Steel: The machine AM 75 produces up to 6.600 laces per hour. This means, the machine must bring the lace up to 6.600 times per hour, approximate twice per second, from the left to the right four prong spider, where the lace is measured and wrapped arround. If the lace has a length of 1 m for example, the transfer-carrier (the frog) runs in a second from the right turning point to the left and back again. This movement from right to left and back again with a speed of 2 m per second is done by a teeth-bar and a toothed wheel. In our machine they are very strong and have a modul 4. The transfer-carrier (the frog) who runs left and right and carries the endless lace, runs with four bearings on harden and polished steel, nearly without any play. The steel is grinted very exactly. |
 |
| Adjustment of the Fingers and their Pre-opening:
The machine catchs the lace with "fingers", guides it into the die-box, holds them while the tipping and at the end lays the laces into the collecting hooks. Elastic laces have high tension and escape from the fingers. Because of this they cannot be layed into the collecting hooks. Our machine has a special construction which allows to adjust the fingers exactly to the thickness of the lace. More than this the construction opens the fingers in two steps: The first step is the pre-opening which opens the fingers only a little. This "little" can be adjusted and will be exactly so much that the tension of the lace can escape, but the lace itself remains between the fingers. In the second step, when the lace does not have further tension, the fingers open complete. Now the lace falls without problems into the collecting hook. The machine has two counters: One counts the quantity of laces which should be filled into one collecting hook. After this quantity is reached, the collecting hooks are turned. The second counts the quantity of filled collecting hooks. After having reached the pre-choosed quantity, the machine will stop. The acetonepump can be adjusted and pumps
always exactly
the required and adjusted quantity of acetone to the lace. Protection and CE-Sign: |
 |